Use the switch that has the black wire on both terminals and ignore the switch that has a red wire on one of the terminals (or remove it and cover the opening). Note that the ceiling wire go to the remote and the reomte wires go to the fan/light unit. Then wire the remote as shown on Tester101's diagram. If you want direct control of the light and fan from the wall switches, you can usually skip the controller unit in the fan unit, but you lose control of speed and light level.īased on further feedback from the OP, connect the black wire in the ceiling box to the black wire on the remote unit in the fan. If you plan to use the remote, you can skip the red wire in the ceiling, just cap it off with a wire nut. Either remove the second switch and use a cover plate that has one side blank, or leave the second switch unconnected but in there filling the hole. When it is on, you then can control the various features with the remote, even turning everything off. In that case, the wall switch is a master - when it is off, everything is off. You can also leave a wall switch in the mix. Leave the red wire that was attached to the second switch unconnected, cap it with a wire nut, and put a blank cover over the old switch box. If you want this setup, you can remove the switches, and in the box that held the switches, connect the black wire bringing power to the switch directly to the black wire going to the ceiling fan unit. On, off, and level control for the fan and light are all controlled from the remote. Perfect for those without attic access DIYBRY 2.29K subscribers Subscribe 66K views 3 years ago Found my video helpful. In those cases, you follow the diagram in your question using just a black (hot) and a white (neutral), plus a ground going to the remote controller in the fan unit itself. Intro Install separate fan and light controls with a single switch. A picture is posted, as I’m so lost on what to do. When I tested the wires with the switch off one still came back hot. In modern fans with remote controls, the whole fan/light assembly is often set up with no wall switch. My ceiling fan and light will only work with the chain and not the switch. Those hot wires may be the same or different colors, usually black, red and sometimes blue (or even a striped color). The hot wires are separately connected to the hot from the fan and the hot from the light. In the ceiling box, the white wire was connected to the white wires from the light and the fan. There is no firm rule as to which goes to which. The neutral wire was for both the fan and light, but the hot lines were separate. The cable from the switches to the ceiling usually had three wires (plus a ground). In many cases the incoming hot line was connected to two switches, one to control the fan and one to control the lights. There usually was also a ground wire, most commonly bare, but sometimes green. In many older fan/light setups, power came to the wall switch with just two wires, hot (black) and neutral (white). They work the same as blue wires and make light kits function properly by connecting with the main red wire coming from the fan junction box.It sounds like you are converting from a fan that did not have a remote control to one that does. Red secondary wires are seen as an alternative to be used in place of blue wires. This wire provide a connection for the red main or hot wires, so let light kits brighten up the room! The blue wire is indicated as a source for lamps or light if they’re present on ceiling fans. It works as an electricity source for light kits on ceiling fans.Īccording to AskTheElectrician, these red wires from the ceiling connect with the blue wire coming from the fan to make lights function properly. The red primary wire (live or hot) originates from the ceiling fan junction box or main outlet. Differences Between Red Wires & Blue Wire Red and blue ceiling fan wires can be confusing, as they both serve similar purposes, i.e. It can be used for any device that requires electricity, such as a lamp or a ceiling fan.Connect the Green / Yellow Wire as ground wire from the fan to the household. The light switch red wire carries electricity from the power source to the light and appliance outlets. Wiring a Ceiling Fan with Pull Chain & Light Control by Separate SPST Switch.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |